The function and adjustment of offset printing machine's water transfer mechanism (I)

The quality of offset printing products is inseparable from the balance between ink and water. In the printing process, the amount of water supplied is too large or too small, which is often prone to occur because the size of the printing plate moisture is manifested from the dirtiness of the printing plate. However, the so-called dirt is caused not only by the small amount of water, operators often mistakenly increase the loss of balance between ink and moisture caused by the amount of water, creating a vicious cycle. Now let's analyze what kind of printing consequences are caused by excess water:

1. Dilute the ink to make the ink lighter and dull, affecting the color of the printed product. If we use the method of increasing the amount of ink to save the ink color, it will cause the ink to be large and the water to be large, making the image thick and fuzzy, and the imprinting is not clear.

2. Cause ink roller to deink. In severe cases, there will be accumulation of moisture on the entire ink roller, so that the graphic part of the printing plate will not be supplied with the normal amount of ink, causing the plate graphic to “fabricate”.

3. Affect the drying of the blot. If the ink is mixed with excessive moisture, the ink drying will be inhibited. Together with the absorption of more moisture in the paper, the product will dry more slowly.

4. The paper fiber absorbs too much moisture, which will cause deformation, resulting in inaccurate overprinting. It will also loosen the texture of the paper, seriously affecting the quality of printed products.

5. The ink emulsifies and the ink loses its viscosity. After the ink is emulsified, it can't protect the printing plate picture and text, it is easy to cause "flower plate", at the same time it will reduce the printing plate's resistance to printing force.

Through the above analysis, it is illustrated that the balance between ink and ink is a key link in offset printing. In addition to the experience of the operator, it is more important to master the correct use and adjustment of the offset printing machine's water delivery mechanism. I will briefly introduce how to use and adjust the water delivery mechanisms of the J2108, J2203, and J2205 offset presses produced by the Beijing People's Machine Factory.

In order to adapt the water supply capacity of the water delivery system to the requirements of the printing production, the water delivery system is provided with a device for controlling the moisture and regulating the amount of water. This can be divided into three parts according to the nature of their work: First, the water supply device; Second, the uniform water device; Third, the water supply device.

The water supply device mainly consists of a water tank, a fountain roller, and a water transfer roller. The sink is used to store water, and there is a water bucket roller (also called water outlet roller) at the upper part. The lower half of the fountain roller is immersed in the fountain solution. They do not touch each other and do not support each other. In addition to automatically adding water to the water (it has been used by many manufacturers), it is also possible to add water manually.

Manually adding water requires the operator to constantly add the previously prepared solution to the sink. Since the amount of water supplied in the fountain roller is related to the height of the fountain solution, the water supply must be uniform so that the fountain solution in the sink must maintain a certain water level.

The operator can't be impatient when adding the water bucket solution. Slowly add the water bucket solution to the water tank, and do not swing the solution in the water tank. If it is shaken up, the local moisture will suddenly increase during normal printing, which will affect the quality of the product. Second, the water bucket solution will be sprinkled on the front part of the sink, resulting in abnormal feeding and clutch pressure (this is because The solution drips into the front teeth of the gauge to form a conductive layer; the third is dropping onto the printed product, resulting in spots on the paper, which are likely to appear double when printing.

The water transfer roller, also known as the draught roller, is a rubber roller installed between the water roller and the water roller. The regulation requirement of the water transfer roller is that the draught should be kept in parallel with the water roller, and there is an appropriate pressure, which is regulated by the tension springs on both sides. The tension of the tension spring must be kept constant during adjustment to ensure that the water transfer roller works in parallel with the water roller during draught. When the water is supplied, it depends on the cam. When adjusting, the water transfer roller must be leaned on the string water roller and there is proper pressure. On both sides of the water roller there is an adjustment screw and a positioning backing. The adjustment also requires that the transfer roller and the skewer roller are parallel.
The water transfer roller also has a draft device for draught. When the pressure is applied to the printing, the normal draught feed water is oscillated back and forth through a 0.7 kg iron suction of 220V. When the pressure is released, it stops swinging back and forth, that is, no longer depends on the outlet roller. The buttons for controlling the water supply and water supply on the operation console are to control the iron absorption. They work according to the production conditions.

We sometimes find out that after the normal printing, the pressure of the platen becomes larger after the pressure is released. Why? This is because after the iron work is stopped, the pulling force of the top claw puller next to the iron sucker is not enough, and the roller is still draught after the roller is separated from the pressure. The machine stops the draught after running one or two turns. The force of the claw pull spring is not enough, causing the suction iron to retract slowly one or two beats. This is the reason that caused the layout moisture to increase. To solve this problem is very easy to do, just replace a new tension spring or shorten the old tension spring by one or two. (to be continued)