[ Chinese wardrobe net ] Because the size of the bedroom is different, the type of style selected may be different, but for the installation of the wardrobe , it is basically the same, whether it is finished wardrobe or assembly wardrobe, custom wardrobe installation. All need to be done, then what are the precautions for the wardrobe installation? Second, how to install a custom closet? Wardrobe installation notes: 1. Use a mat to place the floor. Start by assembling the wide side panel against the end of the wall. Place the wide side panel on the ground (maintain 700mm away from the rear wall). First, put the plate of the filled three-in-one rubber plug on the cloth, check the hole spacing and the drawing, and install the three-in-one single-link. Then the solid layer is nailed to the cork, fixed on the wide side plate, the top handle with the large handle hole facing upward, the other solid layers are facing downward, and the foot line large handle hole is facing inward (the middle solid layer is consistent with the L frame height, that is, the bottom plate to the solid layer The inner space is 960mm, and the hole is drilled on site.) Put the side panels, nail the cork, and the cork is required to connect the solid layers on both sides. Install the double connecting rod on the second cabinet. Note that the large handle on the double connecting rod can only lock half, that is, 90°. When the two solid layers are fixed to the side plates, tighten the large handles at the same time. Repeat the installation steps for the second cabinet when installing the third cabinet. 2, nail back board. Place the assembled whole cabinet on the floor of the point cloth, and lay the side panels in the same plane. Use a slider to measure the diagonal size of the cabinet and adjust it to the same level. Start with the first backing plate from the wide measuring board. Note that if there is a solid nail in the middle, draw the center line of the solid layer with a pencil and nail it. nail. 3. Installation of the L frame. Use the side plates of the L frame to have a parallel line on the corresponding side plates, then move the center line of the three-in-one rubber particles up by 9 mm, and draw a parallel line on the corresponding bottom plate with the top frame of the L frame. The inner center 9mm draws the center line of three rubber pieces. The hole was drilled with a 10 mm drill bit and the hole depth was 10-20 mm. Install a single pole. After the L frame is installed, nails are fixed on the back plate. 4, clean the wardrobe installation debris, left and right station one person, the wardrobe is slightly inclined backwards, forcefully lifted, moved back to the desired position, pay attention not to scratch the floor, the wall. 5. Install three sections of track: the track is placed against the drawer, the drawer floor is flush, and the moving mother rail fixed sub-rail screw is mounted on the sub-track vertical eye (this is adjustable). The distance between the two drawer panels to the center of the track eye is further increased by 2 mm. The data of the female rails is removed and the transverse line is drawn on the side panel of the cabinet with a 90° angle. The cross-sectional line is the center line of the female rail. . The drawer panel is inserted into the column, so the vertical cut line is drawn from the outer side of the side panel of the cabinet, the female rail is flush with the vertical tangent line, the center eye is flush with the line, and the screw is mounted on the transverse eye of the busbar (adjustable position). After the drawer is installed, the adjustable position is used for debugging, so that the drawer surface is flat and the surrounding gap is even. Finally, the fixing screws are placed on the transverse eye of the sub-track and on the vertical eye of the female rail. How to install a custom closet? First, the preparation stage 1. Material is present More formal furniture manufacturers, cardboard packaging is generally shipped to the site. After unpacking, check the plates and hardware. 2. Fixing screws The nails are generally left on the plates according to the design drawings, and the workers at the site use special tools to fix the screws. 3. Measuring side panels Since the closet is placed against the wall, the side panel is sawn off at the position of the baseboard. After you have it, look it up and see if it fits. Second, the installation phase 1. Place the bottom plate The floor placed on the bottom of the wardrobe should be cleaned beforehand, because it will be troublesome to clean up after installation. 2. Fixed frame Install the side and back panels of the closet according to the grooves on the board and adjust the position between the boards. 3. Install the top plate Prepare a bench for climbing, the top plate should be lifted up and then fixed with rivets. 4. Mounting shelf Place the shelf where you have previously screwed it and then secure it. Pay attention to the fixed position of the shelf and the back and side panels. 5. Fixed door rail The door rails are installed on the top and bottom sides of the wardrobe. The material of the door rails is better, lighter and firmer. 6. Install the clothes rail Fix the rivets in the reserved position and install the clothes rail. Note that the two sides should be balanced.
1. Sit Stand Workstation Lift freely, can stand can sit alternate office, stand sit alternate do not hinder busy business at hand.
2. It's easy to operate, just press the button to achieve the purpose of alternate standing and sitting.
3. Memory function storage: that is, the user can adjust the function key to a suitable height according to his own height, and adjust the function key to a fixed position to facilitate the fixed position and use.
4. The appearance is simple and generous, which is in line with the international office trend and different from the traditional desk style which is dull and not easy to move.
5. It is beneficial to the physical and mental health of office workers, increases work efficiency, enlivens the workplace atmosphere and makes the workplace atmosphere more active.
Sit Stand Workstation,Stand up desk workstation,Sit Stand Desk Workstation,Adjustable Work Tables,Sit Stand Laptop Desk Suzhou Uplift Intelligent Technology Co., Ltd , https://www.upliftecdesks.com
